Overview

CarSTOP CS-7000 - immobilizer system is a new generation anti-theft system with the most advanced technology – dialogue code 2,4 GHz. It not only prevents theft, but also prevents carjacking. This system could install on any vehicle while won't destroy the original electrical system It is very difficult for a theft to find an alarm system had been installed in the vehicle, as the driver no need to make any operation but only take the key into the range of communication. But be sure the key should be within range of 3-5 meters. This system also can work very well with a car alarm with engine start function.

Operation

If the smart key is within range of 3~5 meters, the system will be activated automatically, a melody sound emits from the system and LED flashing from the key to confirm the communication is successfully. If the key is out of range 5 meters, when engine started for 5~7 seconds, the system will alarm max 10 seconds continuously, furthermore, the sound's speed is faster and faster in last 5 seconds to warn the driver that the engine will die off, but the system won't die off if the car is stopped moving during alarming, if your car moves again, your car will die off immediately, because this system is built-m an advanced accelerometer sensor

Anti-carjacking

In anti-carjacking mode, the system forces to shut off engine, prevent possibility of any carjacking In case the key is lost during driving (that means the anti-carjacking is activated), the system allows the engine working for 60 seconds (it's security guarantee's requests during driving), then following 30 seconds for melody alarming (25 seconds for intermittent alarm as reminding, following 5 seconds for urgent alarming) If the vehicle is parked well before alarming stop, it allows the engine keep working without car running. Once the vehicle is attempt to run, the system will immobilize the engine immediately In any case, if the system can not detect any signal from the key, when engine is started, there would be melody music emits as reminding for PIN code entering, and then 10 single-tone signals In case entering error, a remind melody music also emits. When the key is in range, the system would unlock the engine. Normally the battery can be used for at least half of one year or longer, then the battery should be replaced in time. After Ignition on, if the siren beeps 3 sounds per one minute means it should be replaced with a new battery. It is suggested to put a spare CR2032 battery inside the car for emergency using If alarming during driving, it should be stopped within 30 seconds before engine immobilized. When the vehicle is in engine immobilized status, the steering wheel will be stiffen to turn or even hard to press the footbrake, because the fluid amplifier stop working in this situation It is very dangerous especially when car is running in high speed Don't put the key inside wallet or together with car key.

Valet/service mode

If you have to park the vehicle for service, and you don't want to expose you installed alarm system, it is suggested that put the key in a hidden place inside the car to stay for awhile.

Check proper working of smart key

If the smart key is already in the vehicle but no melody music emits, it has to be checked Use a knife to open the case of smart key, adjust the CR2032 battery. If it is in good condition, the LED will flash 3 times. If low level power in the battery, the LED flashing turns very weak If no flashing at all, means no power in the battery.

Change battery.

When engine starting, if the system beeps 3 sounds every other one minute, it means low level power It has to replace it with a new battery Use a knife to open the case of smart key and replace it then close the case Please aware that polarity of battery should be correct

Note: You have to install the battery before using.

PIN Code activated

The PIN code consists of 3 digits. Keep out of working range and ignition on, the system will alarm for 60 seconds. When the alarming sound stops, ignition off then ignition on immediately, the interim time should not exceed 1 second.

When engine starting for about 8 seconds, melody sound signal emits once as reminding for enter the first number. Then 10 "Di" sound signals emit, count the "Di" sound signals until the number of sound signal coincides with the first digit of the PIN code, then turn off the ignition (The first digit of the PIN code has been entered). For example, ignition off when you hear the first "Di" sound signal means you are entering "1" digit, ignition off when you hear the tenth "Di" sound signal means you are entering "0" digit.

Turn on the ignition, melody sound signal emits twice as reminding for entering the second number. Then 10 "Di" sound signals emit, count the "Di" sound signals until the number of sound signal coincides with the second digit of the PIN code, then turn off the ignition.

Turn on the ignition, melody sound signal emits three times as reminding for entering the third number. Then 10 "Di" sound signals emit, count the "Di" sound signals until the number of sound signal coincides with the third digit of the PIN code, then turn off the ignition.

If you are entering the wrong number, one melody sound signal also emits as reminding, the system would go back to the status of password entering.

If the password entered is correct, 5 „Di-” long sound signals would be emitted (each "Di" sound signal will last for 5 seconds). If you turn off the ignition when you hear the third „Di-” long sound signals, and ignition on again, the system will go into service mode (the buzzer will "Di" once per one minute). If the system detects the smart key for 70 seconds, it will exit the service mode automatically.

Note: Before entering service mode, please make sure at least one smart key has been programmed.

Enter system controlling mode.

Keep smart key out of range, or take the battery out from the smart key. Follow the above steps to enter password. If the entered password is correct, the system will emit 5 „Di-” long sound signals (each signal will last for 5 seconds).

For entering code learning mode, the ignition should be turned off when you hear the first „Di-” sound signal.

For entering password setting mode, the ignition should be turned off when you hear the second „Di-” sound signal.

For entering service mode, the ignition should be turned off when you hear the third „Di-” sound signal.

For turn off anti-carjacking mode, the ignition should be turned off when you hear the fourth „Di-” signal.

For turn on anti-carjacking mode, the ignition should be turned off when you hear the fifth „Di-” sound signal. (Factory default setting is anti-carjacking mode on).

Enter system controlling mode

Smart key operation

Five keys are allows to be programmed. Please make sure the key you are going to program is equipped with battery, the other keys should not be equipped with battery. Enter into code learning mode, and ignition on, a melody emits for code learning. Put the battery into the key for code learning one by one It will confirm with three sounds if code learning is successful If there is no any melody reminding means unsuccessful code learning In this case please take off battery and reinstall it.

Note: There will come with three sounds as confirmation whichever key is finished to I be programmed. All transmitters must be programmed in one time, as it will delete the previous programming record during programming. Die out the engine to exit the code learning mode.

PIN code setting

PIN code is consisting of three digits, the factory default setting is "111" Enter into PIN code setting mode. (See PIN code activated)

  1. Turn on the ignition. One melody sound signal emits as reminding to enter the first number.
    Then ten "Di" sound signals emit, count the "Di" sound signal until the number coincides with the first digit of the PIN code, then turn off the ignition.
  2. Turn on the ignition, two melody sound signals emit as reminding to enter the second number.
    Then ten "Di" sound signals emit, count the "Di" sound signal until the number coincides with the second digit of the PIN code, then turn off the ignition.
  3. Turn on the ignition, three melody sound signals emit as reminding to enter the third number.

Then ten "Di" sound signals emit, count the "Di" sound signals until the number coincides with the third digit of the PIN code, then turn off the ignition.

When finished the above processes mean three password digits have been entered in the status, however the new password should be confirmed to be effective Just repeat the above steps to confirm the password.

Note When changing the password, you should take measures to prevent forgetting or lost t password Once lost the password, you won't have the possibility to be supplied new smart key and eliminate the old smart key's PIN code.

Anti-carjacking ON/OFF

Enter system controlling mode.

For turn off anti-carjacking mode, the ignition should be turned off when you hear the fourth "Di-"sound signal, then ignition on, the Anti-carjacking mode is off now. Note Anti-carjacking is off, the alarm system doesn't be protected.

For turn on anti-carjacking mode, the ignition should be turned off when you hear the fifth "Di-"sound signal, then ignition on, the Anti-carjacking mode is on now (The factory default setting is anti-carjacking mode on).

Accelerometer sensor operation

Accelerometer sensor operation

Turn on the ignition, take the smart key out from sensing range, the buzzer will beep 5 seconds urgently. If the vehicle attempts to move, the engine will be immobilized until the smart key comes into sensing range. A melody emits from buzzer when the system has detected the smart key, the alarm system's engine will be unlocked.

Turn on the ignition, if the smart key is not in sensing range, there will be signals emits for PIN code entering. If the vehicle attempts to move, the engine will be immobilized immediately. After 6 seconds the engine will be unlocked, but at each attempt to drive, the engine will be immobilized again until the smart key is within sensing range. A melody emits from buzzer when the engine is unlocked.

Installation guide

This system is designed to install in vehicle or motorcycle with 12V power supply.

This brain unit should be installed in a hidden place For example, it can be installed in the engine hood or in the passenger cabin, avoid the place with high temperature and caustic substance If possible please place this unit far from metal parts for at least 12 centimeters so as to avoid wireless transmission jamming. The unit should no be fully covered.

Connect wire 4 for power supply

Connect wire 1 for GND

Wire 2 and 6 are connected through relay inside. The relay contact should be in closed circuit as NC. For long-term using, the current should not larger than 10A. For short time using (within 1 minute), the max current should be 20A.

When installation is carried out, any electrical risk should be taken into consideration.

Wire 5 is for auxiliary output, no need connection

Connect black wire of buzzer with wire 3. Connect red wire of buzzer with wire 4. When ignition on there should have 12V power supply, and when ignition off, the power supply should be cut off.

This system can work without buzzer, but you will be unable to receive any alarming information that will cause the problem of system setting.

We will not install the battery inside the smart key for the purpose of preventing power loss, but the completed set should include the CR2032 battery. Before battery installation, please check if the battery is on valid date, and its surface is on good condition

Note: After installation finished, you have to check if the system is working properly, and then change the PIN code.

System diagnose

During installation or using this system, it may have to check system working. To check the condition of the battery, open the casing of key, and remove the battery from the element plate, then put the battery back in the contact holder in line with the indicated polarity. Observe the operation of the LED If it is flashing 3 times means the battery is in good condition If it is flashing but very weak, means power level is very low If the LED doesn't flash, replace the battery with a new one.

To check proper working of wireless communication system, turn on the ignition, if the key is within sensing range, melodic music emits from buzzer, means the wireless communication is in good condition.

Sound signals from the buzzer

If the brain unit module doesn't detect the signal of the smart key after loaded the CR2032 battery, one "Di" sound signal per one second, total 5 sounds in 5 seconds.

During driving, if the brain unit module doesn't detect the signal of the smart key, 60 seconds later, one "Di" sound signal per one second, total 25 sounds within 25 seconds, and then one "Di" sound signal per 0.5 second means the engine will be immobilized within 5 seconds.

When ignition on, if there will be three "Di" sound signals per one minute, means low power level of battery and remind you replacing the new battery soon.

One sound signal per one minutes, means the system is in service mode.

Melody sound signal for entering PIN code

One signal ("Di" sound) per two seconds 10 times for entering PIN digits
One signal (melody sound and "Di" sound) per two seconds 10 times for confirming PIN code
Five "Di-" long sound signals (each signal last for 5 seconds) for entering system controlling mode.
Melody sound for PIN code changing.
Melody sound for PIN code entering error.
Melody sound for system attempts to communicate.

Completed set includes:

  1. Brain unit module x 1 pc
  2. Smart key x 2 pes
  3. Buzzer  x 1 pc
  4. Tapes (120~150mm) x 3 pcs
  5. Grounding wire contacting  x 1 pc
  6. User manual x 1 pc
  7. Leather cover  x 1 pc
  8. Package box x 1 pc
  9. Key chain x 2 pcs

Technical specifications:

  • Operation current <21mA
  • Operation current in anti-carjacking <85 mA
  • Key operation current < 10mA
  • Brain unit operation voltage 9~15V
  • Radiofrequency 2 4~2 5GHz
  • Radiation intensity <0 MB7
  • Operation temperature; -40°C~+85°C
  • Max Current of brain unit 20A
  • Brain unit size 68x26xllmm
  • Smartkey size 51x33x5mm
  • Battery CR2032,3V
  • Wires length from brain unit 50cm
  • Wires length from buzzer 50cm

After installation finished, please keep the user manual for future reference.

Attention Keep the user manual away inside the car, the best place would be the robber can’t find it.

Wiring diagram CarSTOP CS-7000

Пожалуйста, Оцените материал 5 1 1 1 1 1 1 1 1 1 1 Рейтинг 0.00 [0 Голоса (ов)]